Scansonic L20 Floorstanding Speaker
Original price was: 1 995,00 €.1 000,00 €Current price is: 1 000,00 €.
The Scansonic L20 is a passive 3-way floorstanding speaker for stereo and home cinema systems. It uses three 6.5-inch bass drivers, while a dedicated midrange driver divides the reproduction duties. Its 4-ohm nominal impedance requires an amplifier designed for that load. The slim MDF cabinet has a walnut finish and an additional 15 mm front panel.
The Scansonic L20 floorstanding speaker is a passive 3-way model designed for stereo and home cinema systems. It uses three 6.5-inch bass drivers, complemented by a dedicated midrange driver and a silk-dome tweeter.
This is not an active speaker, so it requires a separate amplifier and speaker cable.
3-way design and cabinet
Three 6.5-inch drivers reproduce the bass frequencies, while a 5.25-inch driver handles the midrange. This division allows each driver to operate within its intended frequency range.
The 25 mm tweeter features a silk dome. The seller associates this design with light, airy treble reproduction. Together with the dedicated midrange driver, it is intended to provide more informative reproduction and more precise spatial imaging.
The MDF cabinet is reinforced by an additional 15 mm front panel intended to reduce unwanted vibration and resonance. A walnut finish, traditional proportions and Scandinavian lines give the cabinet an understated appearance.
The matching front grille attaches magnetically, making it easy to remove and replace. It is covered in furniture-grade fabric and is included with the speaker.
Connecting the speaker to your system
The speaker has five-way binding posts. Connect a speaker cable between the amplifier’s speaker outputs and these terminals. The cable terminations must be physically compatible with the binding posts.
Make sure that both channels are connected with the same polarity. This keeps a pair of speakers in phase and prevents weakening of the central stereo image. Volume and channel balance are controlled through the amplifier or AV receiver.
The 4-ohm nominal impedance is an important consideration when choosing an amplifier. Select a model whose operating instructions explicitly permit the connection of 4-ohm speakers. A minimum-impedance curve is not provided, so adequate amplifier headroom remains important.
Understanding the power and sensitivity figures
The stated ratings are 150 W nominal power and 220 W maximum power. These figures should not be treated as a requirement to choose an amplifier with exactly the same output rating. No definition of the power ratings or measurement conditions is provided.
The 90 dB sensitivity figure is also listed without measurement conditions. Comparing different speakers solely on this value may therefore be misleading. Likewise, the 35 Hz-20 kHz frequency range should be treated as a general guide because no tolerance or measurement conditions are specified.
Placement and initial adjustment
At 210 mm wide and 1090 mm high, the cabinet is tall and narrow. Its net weight of 18.75 kg calls for a firm, level surface. When planning its position, allow additional clearance for the grille and spikes.
The included spikes help you level the speaker accurately. Use protective discs beneath them on delicate flooring. Level the cabinet first, and only then adjust the direction in which it faces.
When using two speakers, begin with a symmetrical arrangement relative to the listening position. Turn them inward in small increments and assess every change from the main listening seat.
Distance from the walls affects bass balance. Start with some space between the speakers and the rear wall, then compare several positions. In a home cinema system, configure channel levels and distances through the AV receiver.
Technical specifications
| Model | Scansonic L20 |
|---|---|
| Type | Passive 3-way floorstanding speaker |
| Application | Stereo and home cinema systems |
| Tweeter | 1 × 1 inch, 25 mm silk dome |
| Midrange driver | 1 × 5.25 inches |
| Bass drivers | 3 × 6.5 inches |
| Nominal impedance | 4 ohms |
| Sensitivity | 90 dB, measurement conditions not provided |
| Nominal power | 150 W, power definition and measurement conditions not provided |
| Maximum power | 220 W, power definition and measurement conditions not provided |
| Frequency range | 35 Hz-20 kHz, tolerance and measurement conditions not provided |
| Connections | Five-way binding posts |
| Cabinet material | MDF |
| Front panel | Additional 15 mm panel for reducing vibration and resonance |
| Finish | Walnut |
| Front grille | Magnetic, with furniture-grade fabric; included |
| Spikes | Included |
| Dimensions | 210 × 283 × 1090 mm, W × D × H |
| Package dimensions | 290 × 360 × 1210 mm, W × D × H |
| Net weight | 18.75 kg |
| Packaged weight | 19.75 kg |
FAQ
Can the speaker be connected directly to a television or player?
No. This is a passive speaker, so a power amplifier or AV receiver is required between the audio source and the speaker.
What type of amplifier should I choose?
The amplifier must be suitable for use with 4-ohm speakers. A matching power figure alone does not confirm compatibility, so first check the permitted speaker load.
Is a 150 W amplifier required?
No. The 150 W figure is the speaker’s stated nominal power rating, not a required amplifier output. The power definition and measurement conditions are not provided.
How should I begin adjusting the speaker positions?
Place the speakers symmetrically and leave some space behind them. Then adjust their inward angle gradually, assessing the result from the listening position.
How can the L20 be used in a home cinema system?
Two speakers can be used as the front left and right channels. Connect them to the corresponding speaker outputs on the AV receiver.
What is included?
The speaker includes a magnetic front grille covered in furniture-grade fabric and a set of speaker spikes.
