Magnat Interior ICP 52 In-Wall and In-Ceiling Speaker
80,00 €
Magnat Interior ICP 52 is a passive installation speaker for an in-wall or in-ceiling sound system. Its swivelling 20 mm tweeter helps direct the sound towards the listening position, while three-level tweeter adjustment allows the presentation to be matched to the room. The moisture-resistant construction is suitable for bathrooms, spa areas and covered outdoor spaces where the speaker is not exposed directly to water.
Magnat Interior ICP 52 is a passive two-way installation speaker designed for in-wall or in-ceiling mounting. It is suitable for a permanent sound system where the speaker enclosure needs to remain concealed within the structure. Moisture-resistant materials allow the speaker to be used in bathrooms, spa areas and covered outdoor spaces.
The speaker requires an external amplifier with a recommended output of 20 to 120 W. Its 8-ohm nominal impedance helps you assess electrical compatibility with the chosen amplifier.
Drivers and sound direction
The 130 mm woofer features a moisture-resistant hairline polypropylene cone. A long-throw rubber surround gives the cone the freedom of movement required for low-frequency reproduction.
The 20 mm PET dome tweeter can be swivelled by up to 35 degrees. After installation, the high frequencies can therefore be directed towards the main listening position. This is especially useful when the mounting point is not located directly above the listener.
Adjusting the sound during installation
The crossover provides three-level tweeter adjustment. Begin with the middle setting and assess the sound from your usual listening position. The higher or lower setting can then be used to balance the presentation according to the room acoustics and the speaker’s placement.
Adjust the direction of the swivelling tweeter and its output level together. Set the dispersion direction first, then fine-tune the level. This helps prevent unnecessary emphasis of the high frequencies.
Connecting the speaker to your system
This is a passive speaker, so it must be connected by speaker cable to the speaker outputs of an amplifier. It does not have an integrated amplifier and is not intended for direct connection to a line-level audio output.
For a stereo system, provide a separate speaker for the left and right channels. Route the cables before closing the wall or ceiling structure, and maintain matching polarity on both channels.
Preparing the installation location
Installation requires a 168 mm circular cutout and at least 81 mm of clear mounting depth. Before cutting, check the structure for framing, pipes or electrical cables. The 202 mm outer diameter indicates how much space the visible part of the installed speaker will occupy.
When fitted in a ceiling, the speaker functions as a compact recessed sound source. For in-wall installation, the tweeter can be directed towards the listening area. The mounting surface must be stable enough to support the speaker’s weight of one kilogram.
The construction is moisture-resistant, but no IP protection rating is specified. Do not install the speaker where it will be exposed directly to water. In a covered outdoor area, it must remain protected from rain and water splashes.
Included accessories
The package includes a protective grille and a cutting template. The template helps you mark the circular installation opening accurately, while the grille covers the drivers after the speaker has been installed.
Technical specifications
| Type | Passive in-wall or in-ceiling speaker |
| Operating principle | 2-way |
| Woofer | 1 × 130 mm (5.25 in), polypropylene cone |
| Woofer surround | Long-throw rubber surround |
| Tweeter | 1 × 20 mm (0.75 in) PET dome |
| Tweeter direction adjustment | Swivels by up to 35° |
| Tweeter level adjustment | 3 levels |
| Power handling | 60 W RMS / 100 W maximum |
| Recommended amplifier power | 20-120 W |
| Nominal impedance | 8 ohms |
| Sensitivity | 89 dB at 2.8 V / 1 m |
| Frequency range | 38-24,000 Hz |
| Crossover frequency | 4,000 Hz |
| Outer diameter | 202 mm |
| Cutout diameter | 168 mm |
| Mounting depth | 81 mm |
| Weight | 1.0 kg |
| Environmental resistance | Moisture-resistant construction; IP rating not specified |
FAQ
Does the speaker require a separate amplifier?
Yes. This is a passive model without an integrated amplifier. Choose an amplifier suitable for an 8-ohm load and connect the speaker to its speaker outputs.
How many speakers are required for a stereo system?
A stereo system requires one speaker for each channel. Position the two speakers at similar distances from the main listening location.
How should I aim the tweeter?
Swivel it towards the main listening area. Choose the final position while listening from the place where you will usually be seated or standing.
Can the speaker be installed in a bathroom?
Yes. Its moisture-resistant materials are suitable for humid rooms. The speaker is not intended for direct exposure to water or rain.
What must I check before cutting the opening?
Confirm that sufficient mounting depth is available and check for obstacles inside the structure. Use the supplied cutting template to mark the exact position and outline of the opening.
Related products and categories
Related products
