RCA Anti-Static Turntable Mat (Felt) 12″
Original price was: 15,00 €.10,00 €Current price is: 10,00 €.
RCA anti-static turntable mat is a platter accessory intended for 12-inch vinyl records. Its felt surface forms a supporting layer between the turntable platter and the record. The manufacturer describes the mat as anti-static. This grey mat measures 295 × 295 × 3 mm and weighs 45 g. When replacing a mat of a different thickness, the tonearm height may need to be adjusted.
RCA Anti-Static Turntable Mat (Felt) 12″ is a turntable platter mat intended for 12-inch vinyl records. It is placed on the turntable platter, where it forms a supporting layer between the platter and the record. The manufacturer describes this mat as anti-static.
This version is suitable for buyers looking for a grey, lightweight mat with a thickness of 3 mm. Before choosing it, the most important details to check are the dimensions of the turntable platter and the thickness of the mat currently being used. The 12-inch designation explains the intended record format, but the physical dimensions and the turntable’s mechanical setup still need to be considered separately.
Felt construction
The felt construction provides a soft surface on which the vinyl record rests. The material forms the direct contact layer between the record and the turntable platter during use. Its grey colour gives the mat a neutral appearance. Colour does not affect the operation of the turntable or the way the turntable is connected to the rest of an audio system.
The mat weighs 45 g, so this is the amount of additional mass placed on the platter. Although the mat is lightweight, its stated weight may still be relevant when it is used with a particularly light platter or a sensitive suspended turntable design. Buyers using this type of equipment should take the added mass into account when checking whether the mat is appropriate for their setup.
Dimensions and selection
The mat measures 295 × 295 × 3 mm. The first two measurements describe the area it occupies on the turntable platter. They allow the buyer to compare the mat with the available platter surface before purchase. The third measurement is the mat’s thickness, which is important because it determines how much the record is raised above the platter.
The 12-inch format refers to the intended vinyl record size. It does not, by itself, confirm compatibility with every turntable. The 295 × 295 mm surface must fit properly on the platter, while the 3 mm thickness must suit the geometry of the individual turntable. Checking both aspects is particularly important when replacing an existing platter mat rather than installing one on a turntable that is currently used without a mat.
When comparing this product with the original or current mat, do not rely only on the record format. Two mats intended for 12-inch records may still differ in diameter, thickness, weight, or material. For this RCA felt version, the relevant supported measurements are the stated overall dimensions and 45 g weight.
Placement and turntable adjustment
Place the mat directly and evenly on a clean turntable platter. It should lie flat across the available surface. Dust, creases, or other uneven areas should not remain underneath it, as these can prevent the felt from sitting level. Once the mat is correctly positioned, place the vinyl record on the upper felt surface.
Because this mat is 3 mm thick, it can change the height of the record in relation to the stylus, especially when the previous mat had a different thickness. On turntables with adjustable tonearm height, the tonearm position may therefore need to be corrected after the mat is changed. The relevant comparison is between the thickness of the previous supporting layer and the 3 mm thickness of this mat.
If the replacement mat is the same thickness as the previous one, the height difference may be limited. Nevertheless, the turntable’s mechanical setup should determine whether an adjustment is necessary. The product’s 12-inch designation does not replace this check, since record size and tonearm geometry are separate considerations.
Use in an audio system
This is a mechanical turntable accessory used only on the platter. It has no audio connectors, power connectors, or electrical controls, and it is not connected to an amplifier. Installing the mat therefore does not change the turntable’s electrical connection to the audio system.
The same principle applies whether the turntable is used as part of a stereo system or a home cinema system. Compatibility depends on the turntable platter and its mechanical configuration, not on the amplifier, receiver, or speaker connections elsewhere in the system.
Technical specifications
| Product type | Anti-static turntable platter mat |
|---|---|
| Material | Felt |
| Intended format | 12-inch vinyl records |
| Colour | Grey |
| Dimensions | 295 × 295 × 3 mm |
| Weight | 45 g |
FAQ
Does this mat fit every turntable?
Suitability depends on the size of the turntable platter and the turntable’s mechanical setup. The mat covers an area of 295 × 295 mm and is 3 mm thick. Compare these measurements with the platter and the existing mat rather than assuming that the 12-inch designation guarantees a fit.
Does it need to be connected to an amplifier?
No. This is a mechanical turntable accessory without audio or power connections. It is placed directly on the turntable platter and does not connect to an amplifier, receiver, or any other electrical component.
Do I need to adjust the tonearm after changing the mat?
An adjustment may be necessary if the previous mat had a different thickness. A change in record height can alter the tonearm’s position in relation to the record. On a turntable with adjustable tonearm height, check the setup after installing the 3 mm mat.
Is the mat intended for smaller records?
The declared purpose of this version is use with 12-inch vinyl records. Other record sizes are not specified as a separate intended application for this mat.
What should I check if the mat does not lie flat?
Check that the turntable platter is clean, that no dust or debris is trapped beneath the mat, and that the felt is not creased. Remove any uneven areas and position the mat flat before placing a record on it.
Can it be used in stereo and home cinema systems?
Yes, provided that a suitable turntable is used in the system. The mat itself is independent of the amplifier, receiver, and speaker connections because it is a mechanical accessory placed on the turntable platter.
Can I place it on top of another mat?
Stacking mats increases the total height of the record. Use one mat unless the turntable’s mechanical setup has been configured for the greater combined thickness. This helps avoid introducing an unaccounted-for change in the record’s position relative to the tonearm.
