Alpine BBX-T600 Car Amplifier
90,00 €
Alpine BBX-T600 is a 2-channel car amplifier designed for two speakers or a single 4 Ω load in bridged mode. It delivers 2 × 50 W into 4 Ω or 2 × 70 W into 2 Ω of continuous power. Adjustable high-pass and low-pass filters help tailor the reproduced frequency range to the connected speakers. RCA input sensitivity is adjustable from 0.2 to 8.0 V.
Alpine BBX-T600 car amplifier is a bridgeable 2-channel Class A/B audio power amplifier. It is designed to power two car speakers or a single 4 Ω load in bridged mode. Continuous output is 2 × 50 W into 4 Ω or 2 × 70 W into 2 Ω. Bridged output is 1 × 130 W into 4 Ω. All these ratings are specified at no more than 1% THD+N.
Applications and operating modes
This model is designed to expand an existing in-car audio system. Stereo mode powers two speakers independently. A load of no less than 2 Ω may be connected to each channel.
Bridged mode combines both channels to power a single 4 Ω load. This mode can be used for one subwoofer or another speaker with the appropriate impedance. A load below the stated impedance does not meet the approved power-rating conditions.
RCA signal connection
The audio signal is supplied to the amplifier through an RCA input, so the source unit must have a line-level RCA output. Input sensitivity is adjustable from 0.2 to 8.0 V, allowing the amplifier to be matched to source signals with different output levels.
The sensitivity control is not a volume control. It should be adjusted to suit the output level of the source. Setting the gain too high may cause audible distortion before the desired listening volume is reached.
Crossover settings
The adjustable crossover provides a choice of high-pass or low-pass filtering. The high-pass filter reduces the amount of low-frequency content sent to the speakers. This is useful for door speakers that are not intended to reproduce the deepest bass frequencies.
The low-pass filter limits higher frequencies. Select it when the amplifier is powering a subwoofer. Begin with a cutoff setting suited to the connected speaker system, then listen from the normal seating position and check that the frequency ranges blend smoothly.
Bass EQ increases the bass level. Set the input sensitivity and crossover first, and adjust this function afterwards. This makes it easier to avoid excessive bass and audible distortion.
Planning the installation location
The amplifier measures 250 × 52 × 240 mm. Measure the intended mounting area before installation and allow additional room for the connections and cable bends. Keep the controls conveniently accessible so the input sensitivity, crossover and Bass EQ can be adjusted without removing the unit.
Technical specifications
| Product type | Car audio power amplifier |
|---|---|
| Amplifier class | Class A/B |
| Number of channels | 2 |
| Operating modes | Stereo and bridged |
| Continuous output into 4 Ω | 2 × 50 W, THD+N ≤ 1% |
| Continuous output into 2 Ω | 2 × 70 W, THD+N ≤ 1% |
| Continuous bridged output | 1 × 130 W into 4 Ω, THD+N ≤ 1% |
| Total maximum power | 300 W, not a continuous power rating |
| Minimum stereo load | 2 Ω per channel |
| Bridged-mode load | 4 Ω |
| Signal input | RCA |
| RCA input sensitivity | Adjustable from 0.2 to 8.0 V |
| Crossover | Adjustable, with selectable high-pass or low-pass filtering |
| Bass adjustment | Bass EQ |
| Dimensions | 250 × 52 × 240 mm |
FAQ
When should I use stereo mode, and when should I use bridged mode?
Choose stereo mode for two separate speakers. Bridged mode is intended for one 4 Ω load when two independent channels are not required.
How should I begin adjusting the input sensitivity?
Start with the gain at its lowest setting and set the source to your normal listening volume. Increase the sensitivity gradually until the required level is reached without audible distortion.
Which filter should I choose for door speakers?
A high-pass filter is generally used for door speakers. It limits the deepest frequencies that these speakers are not intended to reproduce.
What should I do if increasing Bass EQ causes distortion?
Reduce the Bass EQ level and check the RCA input sensitivity setting again.
Is a space measuring 250 × 52 × 240 mm sufficient?
Not always. Additional space is required for the connections, cable bends and access to the controls.
Related products and categories
| Kanalų skaičius | 2 kanalų |
|---|
