Pioneer TS-WX710A Active Subwoofer
433,00 €
Pioneer TS-WX710A is an active subwoofer designed to complement a car audio system. Its two 16 cm drivers reproduce frequencies from 20 to 180 Hz. RCA and speaker-level inputs provide two connection options to suit the available head unit. The adjustable 50-135 Hz filter helps integrate the bass with the main speakers. A wired remote with a 6 m cable allows the control position to be planned in the front of the vehicle.
Pioneer TS-WX710A is an active in-car subwoofer with two 16 cm drivers. Its integrated amplification adds low-frequency output to a car audio system without requiring a separate subwoofer amplifier.
Who Is This Subwoofer For?
This model is designed for audio systems that lack the lowest frequencies. Both drivers are installed in a single enclosure.
The 20-180 Hz frequency range covers the bass region. An adjustable filter allows the subwoofer to be matched with the vehicle’s other speakers, helping to prevent unnecessary frequency overlap.
Two Signal Connection Options
Choose the RCA input when the head unit or another signal source has a line-level subwoofer output. This connection sends the signal directly to the active subwoofer.
The speaker-level input is useful when the existing head unit does not have a suitable RCA output. In this case, the signal is taken from an output intended for speakers. This means the subwoofer can be connected to car audio systems with different equipment configurations.
Before installation, check which output is available on your head unit. You can then plan a suitable route for the signal cable in advance. There is no need to use the RCA and speaker-level inputs at the same time.
Adjusting the Bass
The low-pass filter is adjustable from 50 to 135 Hz. It determines the upper frequency up to which the subwoofer supports the main speakers. A lower setting leaves only the deepest frequencies to the subwoofer, while a higher setting expands the bass range it reproduces.
A setting of approximately 80 Hz can be used as a starting point and then adjusted by listening. If you hear a gap between the subwoofer and the main speakers, raise the filter setting slightly. If the bass begins to sound separate from the music, lower the setting.
The filter slope is -12 dB per octave. This means that higher frequencies are reduced gradually rather than cut off abruptly. Make the final assessment from your normal listening position.
Wired Control
The subwoofer includes a wired remote control with a 6 m cable. This cable length allows the control to be positioned in the front of the vehicle. Plan the cable route before permanently securing the enclosure.
Choosing a Location in the Vehicle
Before buying, measure both the installation area and the route through which the enclosure must be moved into position. Its longest dimension is 850 mm, while the other dimensions are 320 and 90 mm. The slim 90 mm dimension is particularly relevant where installation height is limited.
Leave enough room to connect the signal and control cables. The cables should not be sharply bent or trapped against the enclosure. Secure the subwoofer so that it cannot move when the vehicle brakes or changes direction.
Understanding the Technical Data
The nominal input power is 100 W, and sensitivity is 104 dB. Nominal input power should not be confused with the output power of a separate amplifier. This model already contains the amplification required by an active subwoofer.
The frequency range and the adjustable filter range describe different things. The frequency range indicates which frequencies the subwoofer can reproduce. The filter is used to integrate that range with the rest of the car audio system.
Technical Specifications
| Model | Pioneer TS-WX710A |
|---|---|
| Type | Active subwoofer |
| Subwoofer drivers | 2 × 16 cm |
| Nominal input power | 100 W |
| Frequency range | 20-180 Hz |
| Sensitivity | 104 dB |
| Low-pass filter | Adjustable, 50-135 Hz |
| Filter slope | -12 dB per octave |
| Signal inputs | RCA and speaker level |
| Control | Wired remote control |
| Remote-control cable | 6 m |
| Dimensions | 850 × 320 × 90 mm |
FAQ
Does this subwoofer need a separate amplifier?
No. It is an active subwoofer with integrated amplification. Installation still requires a power connection and the chosen audio signal input.
When should I use the RCA input?
Use it when the head unit has a suitable line-level output. If this output is unavailable, the speaker-level connection can be used instead.
How should I set the low-pass filter?
Start with an intermediate setting and listen to how the bass blends with the main speakers. Make further adjustments in small steps.
What does the 50-135 Hz low-pass filter control?
It adjusts the transition between the subwoofer and the main speakers by setting the upper limit of the frequencies sent to the subwoofer.
What should I measure before choosing an installation location?
Check the available space for the 850 × 320 × 90 mm enclosure and the route needed to move it into place. Also allow room for the connectors and cables.
