Sonus Faber GUARNERI TRADITION STAND Speaker Stand
1 799,00 €
Sonus Faber GUARNERI TRADITION STAND is a speaker stand designed for the GUARNERI TRADITION model. It is intended as a dedicated support for this particular speaker rather than as a universal stand. The seller-stated dimensions (width × height × depth) are 758 × 300 × 390 mm; these measurements help you assess the required floor area, total system height and cable route in advance.
Sonus Faber GUARNERI TRADITION STAND is a dedicated speaker stand designed specifically for the GUARNERI TRADITION speaker. It should be chosen as the matching support for this particular model rather than as a universal piece of furniture for other speakers. The seller-stated dimensions (width × height × depth) are 758 × 300 × 390 mm, allowing you to plan the system’s position in the room before installation.
Purpose and model selection
The speaker model is the main selection criterion. This stand is intended specifically for the GUARNERI TRADITION. Matching the Sonus Faber brand alone is not sufficient, as the stand is not specified for other Sonus Faber speakers.
It is a dedicated support made for one particular speaker model. Confirm that your speaker is the GUARNERI TRADITION before ordering rather than relying only on the manufacturer’s name or the stand’s general appearance.
Dimensions and required space
Each of the three seller-stated measurements answers a different room-planning question. The 758 mm width helps you determine how much horizontal space the stand requires. The 390 mm depth is important when checking the available space near a wall, furniture or a walkway.
The seller-stated 300 mm height helps you anticipate the speaker’s position above the floor. Assess the total system height together with the dimensions of the speaker itself. This makes it possible to consider the completed setup in relation to a windowsill, shelving or a screen before deciding on the final location.
Before positioning the system, use the seller-stated measurements to mark out a 758 × 390 mm area on the floor. This shows the footprint occupied by the stand. The marked area does not include the additional room needed for the speaker cable or the distance you choose to leave between the speaker and the wall.
Positioning in the room
Place the stand on a level surface that can accommodate its entire footprint. Make sure that a furniture edge, skirting board or another obstruction does not extend beneath any part of the stand. This is particularly important when planning a position close to a wall, where the usable floor area may be smaller than it first appears.
For a stereo system, provide the left and right speakers with equivalent placement conditions. Begin with a symmetrical arrangement in relation to the listening position. The final spacing and direction of the speakers can then be determined after the stands are in place.
The seller-stated 300 mm stand height must be considered together with the speaker cabinet. Listening geometry depends on the total assembled height as well as the height of the seated listening position. The stand measurement on its own does not define the final position of the speaker drivers in relation to the listener.
Cable planning
Plan the cable route before fixing the final stand location. Consider the seller-stated stand height and the distance from the amplifier to the speaker. The cable should comfortably reach the speaker in the chosen arrangement without pulling on the connection or forcing you to move the stand away from its intended position.
Allow enough slack for practical positioning and final adjustment. Cable space should be assessed separately from the stand’s footprint, particularly when the system is placed near a wall, cabinet or frequently used passage.
Use in an audio system
In a stereo system, a separate support area must be planned for each speaker. The selected layout should maintain an equal distance from both speakers to the listening position as the starting point for setup.
In a home cinema system, also allow sufficient room for walkways and the cable route. The stand’s physical footprint is only one part of the required space, so consider how people will move around the system and where the cable will run before completing the layout.
Preparing to install the system
Start by measuring the intended location and marking the stand’s overall footprint. Next, plan the speaker cable route and identify the listening position. Only then should you establish the final location for the left or right channel.
When preparing a stereo pair, repeat the same measurement on both sides of the room. Do not assess only the apparently free floor area. Take account of opening doors, walkways, furniture edges and the direction from which the cable will approach the speaker.
This preparation helps you check the physical arrangement before placing the speaker on its dedicated support. It also makes it easier to begin with comparable conditions for both channels and then refine the speaker spacing and direction from that consistent starting point.
Technical specifications
| Manufacturer | Sonus Faber |
|---|---|
| Model | GUARNERI TRADITION STAND |
| Product type | Speaker stand |
| Intended for | Sonus Faber GUARNERI TRADITION speaker |
| Dimensions | Seller-stated dimensions (width × height × depth): 758 × 300 × 390 mm |
| Width | 758 mm (seller-stated) |
| Height | 300 mm (seller-stated) |
| Depth | 390 mm (seller-stated) |
FAQ
How many stands are included?
The available seller listing does not specify the quantity included. Confirm the package quantity with the store before purchasing.
Is the stand’s finish specified?
No. The available seller listing does not specify the stand’s finish, so confirm the required variant before placing your order.
How should I plan the cable route?
Measure the distance from the amplifier to the speaker’s final position and leave sufficient cable slack. The cable should not require you to change the intended stand location.
Where should the stand not be placed?
Do not position it where part of the base would rest against or on a skirting board, furniture edge or another obstruction. The stand’s entire footprint must fit on a level surface.
Is the stand suitable for a stereo system?
Yes. Provide equivalent support areas for the left and right speakers and begin with a symmetrical arrangement in relation to the listening position.
What should I check when placing it near a wall?
Consider the stand depth, the skirting board, the cable route and your chosen distance between the speaker and the wall. The marked footprint alone may not represent all the space required.
What should I measure before buying?
Check the seller-stated 758 × 390 mm stand footprint, the total height when combined with the speaker and the additional space needed for the cable.
Are installation accessories specified?
The available seller listing does not specify which accessories are included. If accessories are required for installation, confirm the package contents before purchasing.
