Pioneer TS-WX610A Active Subwoofer
305,00 €
Pioneer TS-WX610A is an active subwoofer for in-car audio systems where a space-saving design is important. Its two 10 cm drivers have polypropylene cones, while the integrated amplifier removes the need for a separate subwoofer amplifier. An adjustable 50-125 Hz low-pass filter helps integrate it with the vehicle’s main speakers.
Pioneer TS-WX610A is a space-saving active subwoofer designed for in-car audio systems. It combines two 10 cm woofers with an integrated amplifier. This arrangement is suitable for adding bass to a system without installing a separate subwoofer power amplifier.
The subwoofer has a specified frequency range of 25-180 Hz and a stated sensitivity of 101 dB. Its adjustable low-pass filter helps integrate the bass output with the vehicle’s other speakers.
Space-saving construction
The enclosure uses two compact drivers with polypropylene cones. Each driver has a diameter of 10 cm, allowing the unit to provide bass through a space-saving design.
The two stated enclosure measurements are 388 × 144.3 mm. Their orientation and the third measurement have not been provided, so the installation position cannot be selected using these figures alone. Before installation, check the complete enclosure and allow enough additional space for the required connections.
The subwoofer weighs 4.9 kg. Its chosen location and mounting surface must be able to support this weight while the vehicle is moving. The drivers use ferrite magnets, so the unit’s weight should be considered when planning a secure installation.
Integrated amplifier
The integrated amplifier means that the subwoofer does not require a separate bass power amplifier. This reduces the number of individual components in the audio system and makes it easier to plan their placement inside the vehicle.
The specified 2 Ω impedance is a technical characteristic of this active system. The TS-WX610A is not a passive 2 Ω subwoofer that requires a separately selected amplifier capable of driving that load. In this model, the woofers and their amplifier form a single active unit.
The specific types of audio input have not been stated. Connections on the subwoofer should therefore be compared with those available from the car stereo or other audio source before purchase.
Adjusting the low-pass filter
The integrated low-pass filter can be adjusted from 50 to 125 Hz. This filter determines the upper frequency up to which the subwoofer supplements the vehicle’s main speakers. It has a slope of -12 dB per octave, so frequencies above the selected point are reduced progressively rather than being cut off abruptly.
A lower filter setting is a sensible starting point when the main speakers reproduce the mid-bass region confidently. A higher setting can be useful when smaller main speakers need more support at low frequencies.
Change the setting in small steps and listen from your usual seating position. If the selected point is too high, the upper-bass region may become overly prominent. If it is too low, there may be a noticeable gap between the output of the subwoofer and the rest of the speaker system.
The aim is a balanced transition rather than bass that sounds separate from the other speakers. Listening from the driver’s seat is important because the cabin, speaker positions and installation location all affect the perceived result.
Frequency range and system balance
The 25-180 Hz frequency range describes the bass region reproduced by the subwoofer. It is not the same as the selected low-pass filter setting. For example, lowering the filter setting allows the unit to be used mainly for the lower portion of its available range.
The stated 101 dB sensitivity should not be considered in isolation from the installation position and system adjustment. The final balance inside a vehicle is also affected by the cabin volume, the performance of the main speakers and the chosen filter setting.
This subwoofer is intended for an in-car audio system, not a home stereo or home cinema system. No compatibility list has been provided for specific vehicles, car stereos or factory-installed audio systems. Buyers should therefore check the available installation space and relevant connections for their own system.
Technical specifications
| Model | Pioneer TS-WX610A |
|---|---|
| Product type | Space-saving active subwoofer |
| Intended use | In-car audio system |
| Woofers | 2 × 10 cm |
| Cone material | Polypropylene (PP) |
| Integrated amplifier | Yes |
| Impedance | 2 Ω |
| Frequency range | 25-180 Hz |
| Sensitivity | 101 dB |
| Adjustable low-pass filter | 50-125 Hz |
| Filter slope | -12 dB per octave |
| Magnets | Ferrite |
| Stated dimensions | 388 × 144.3 mm |
| Weight | 4.9 kg |
FAQ
What is this subwoofer designed for?
It is designed to add bass to an in-car audio system. Its space-saving construction is useful when the available installation space needs to be planned carefully.
Does it require a separate power amplifier?
No. The subwoofer already contains its own dedicated amplifier, so there is no need to select and install a separate power amplifier for the bass drivers.
Can it be connected to any car stereo?
Before purchasing, compare the subwoofer’s connections with those provided by the car stereo or other audio source. The specific input types and a list of compatible car stereos have not been supplied.
Which filter position should I use as a starting point?
Begin with a lower setting and listen to the system from the driver’s seat. Raise the crossover point if there is still an audible gap between the main speakers and the subwoofer.
Does the 180 Hz frequency limit mean that the filter should be set to 180 Hz?
No. The adjustable filter has an upper limit of 125 Hz. The frequency range describes the subwoofer’s reproduction range, while the filter determines the upper limit used during operation.
What should be considered when choosing an installation location?
Allow for the 4.9 kg weight and choose a mounting surface capable of supporting it securely while the vehicle is moving. Sufficient space must also be left for the connections.
Are the stated dimensions sufficient to check the installation space?
No. Only two measurements are stated: 388 × 144.3 mm. Their orientation and the third measurement are not specified, so all enclosure dimensions should be checked before purchasing.
